Installation of a suspended toilet has a lot of undeniable advantages. However, compelling practical and aesthetic priorities are occasionally overshadowed by breakdowns that need to be rectified. Agree, you should not even try to restore plumbing, if you do not know how to repair the installation of the toilet.
We are ready to help you deal with the problem. In our article, we described all the ways to eliminate minor problems and serious violations in the work of suspended plumbing. Valuable recommendations are given on the operation of equipment and the prevention of negative situations.
For you, we have collected and meticulously systematized all the options for damage, thoroughly examined the methods of dealing with them with examples. The information is confirmed by a photo and video guide.
The principle of operation and design of the toilet
The installation system has a similar principle of operation compared to the usual tanks. When you press the water release lever or button, the valve rises in the lower hole of the tank, after which the bowl is washed with water. When the tank becomes empty and the button is released, the valve returns to its original position under its own weight.
Then the automatic filling mechanism of the tank comes into operation. It consists of a shut-off valve that connects to a water supply. The shut-off valve operates synchronously with the float.
When the tank is empty, the float goes down and opens the valve to fill the tank. Water arrives in the tank and the float floats up in parallel. When it reaches a certain high point, the water supply stops and the shutoff valve closes.
Understanding the principle of operation of the toilet will help to properly carry out repair work and quickly identify a malfunction, replacing worn parts with new ones
Today you can often find tanks with an economical drain, where there are two buttons, one of which allows you to use any part of the tank volume.
Types of problems with wall hung toilets
All breakdowns can be divided into several categories, each of which is tied to a specific node of this type of plumbing:
- violation of the integrity of the drain tank;
- a lot of water flows out (the bottom valve does not cope due to wear or clogging);
- malfunctions in the drain mechanism (the tank does not fill or is filled continuously);
- leakage during water supply to the tank (the joints of flexible hoses / fittings are not sufficiently sealed).
Direct repair of the installation for the toilet may concern already smaller elements in the structure. The main complexity of the work is associated with the replacement of components or the whole mechanism in the drain system.
Most of the problems are related to problems in the drain tank, as it has many moving elements that are constantly in the water
Failures can also be caused by a violation of the shape of the frame on which the installation system is located. This applies to low-cost models from dubious manufacturers or fakes. In such products, the frame is made of thin profiles, which can simply bend under the influence of the mass of the tank with water.
Image Gallery
Photo from
Installation - a multifunctional design that is needed to form a support for the plumbing, to supply water to the device and to connect to the sewer outlet
All types of installations, regardless of their design features, are affected by mechanical stress applied during use and tap water, which can clog nodes and lines supplying water
In the flushing cistern of the structure, fittings are placed, which, during illiterate operation, can be damaged in the same way as in a conventional compact
A frequent cause of breakdowns is an incorrect selection of the support system, which does not take into account the bearing capacity of the wall to which it was mounted, and the installation itself
Wall-mounted support structure
Installation Installation Options
Flushing tank design
Selection of the type of bearing capacity
Instructions for Home Masters
Most of the problems in systems with installation or traditional models are associated with the appearance of malfunctions in the tank mechanism. The reason for this may be poor water quality, which over time causes corrosion of metal elements, and also contributes to the deposition of sediment.
If you find that the water has stopped collecting and draining correctly, you will probably have to perform several actions.
# 1: Water in the tank slowly draws
We clean the strainer at the entrance to the tank (if any). You need to disassemble the unit and remove the filter for washing and cleaning with a soft toothbrush. The fractions carried by the water could clog the mesh cells.
Clogging of the mechanism of the built-in tank and violation of the position of the float or valve often cause a slow filling of the tank or stop the operation of the equipment
If there is little water entering the tank, it is necessary to adjust the position of the valve and the float. This can be done by bending the metal lever, ensuring that the float takes the correct position when filling the tank.
We make repair of the float valve. In some cases, it could just be skewed and need to be aligned. In other cases, you need to check the lever that connects the float and valve. In case of communication failure, the valve will constantly block the flow of water even when the float is lowered. Also flush the inlet valve.
# 2: Exhaust valve clogged
After flushing, the tank starts to fill up, but after the float reaches its upper position, water still continues to flow into the tank. Most likely, the valve is clogged due to the fact that there are many inclusions in the water and they are deposited on surfaces.
The intake valve in the absence of a filter at the inlet to the tank can clog quite quickly, so it is recommended to install a coarse cleaner at the inlet
There is no need to completely dismantle the valve - just loosen the mounts a little to remove the rubber gasket.
Rinse it under high pressure and rinse the valve cover. After that, you can assemble.
# 3: The drain button does not work
When you click on the drain button, nothing happens. Flushing problems are associated with malfunctions in the drain valve, in particular, with a connection failure between the valve and the button. In this case, it is best to replace the drain valve.
If you still want to pick up spare parts and make repairs yourself, we recommend that you contact your equipment supplier. A repair kit of another brand will not work.
If the plumbing does not respond when you press the drain button, the fittings are most likely damaged. It is easier to completely replace it than to look for the cause of the breakdown.
# 4: Water leaks regularly
A thin stream of water constantly flows into the bowl. To eliminate the additional costs of water, it is necessary to replace the rubber gasket, which serves to seal the drain hole. A gap formed or a decrease in tightness can cause leakage.
Sometimes the exhaust valve may become deformed after prolonged use. In this case, replacing the rubber gasket will not help and you will have to change the whole mechanism.
Another reason for the leakage of water into the bowl may be the lowering of the emergency tube, which serves to remove excess water. This happens as follows: if the inlet valve and float system is broken, a continuous stream of water will flow directly into the toilet, preventing the bathroom or the bathroom from flooding.
The drain pipe protects from the flood, but can also cause water to leak into the sewer, so you need to adjust its position or the water level in the tank
There are two ways to solve this problem. The first is to raise the emergency tube higher. If there is simply nowhere to raise the tube, then the second method is suitable - lower the float below by doing this with screws. This will slightly reduce the amount of water in the tank and help eliminate leakage.
We make repair of the float valve. In some cases, it could just be skewed and need to be aligned. In case of communication failure, the valve will constantly block the flow of water even when the float is lowered.
Replacing the rubber gasket should solve most of the problems associated with poor water shutoff. Many modern models are devoid of the usual polymer gasket, having a one-piece plastic inlet valve. In this case, you will have to completely change the valve.
# 5: Installation replacement required
The degree of dismantling depends on the design. Some manufacturers produce models with a revision window through which the drain tank can be repaired. For models of popular manufacturers, the drain button is simply dismantled, after which the master gets full access to the mechanism.
The advantages that the installation provides to the interior can be crossed out by the need to dismantle the wall during repairs, behind which all engineering systems are hidden
Unfortunately, not every model has such conveniences, so you often have to dismantle a partition or tile. The possibility of revision must be laid at the stage of installation of the system with installation.
After gaining access to the tank, it is necessary to do the following operations:
- Remove flush key. As a rule, it just needs to be squeezed out from the back so that it falls out of the cordon.
- Remove frame. We unscrew the screws that serve to fix the frame, and then remove the pusher latches. Now the frame can be removed.
- Dismantle the partition. Tighten locks and remove partition.
- Block the water and press the drain button. Repair must not be allowed to turn into a flood.
- Get wet inside the tank with a rag, as working with wet parts is inconvenient.
- Remove reinforcement block and dismantle the inlet valve.
- Remove the drain valve retainer.
Now you can replace any components by assembling in the reverse order. Before changing parts, it is necessary to completely clean the installation site from rust and sediment. To do this, you can use the WD-40 and similar tools.
# 6: Fighting Bowl Defects
The toilet must be repaired in the following cases:
- cracking / chipping;
- cuff wear, which is used to connect to the sewer;
- clogging.
Damage to the bowl could appear after draining the hot liquid, as well as due to mechanical stress. If a crack appears in the lower part of the toilet bowl, you will have to completely change the bowl.
With the formation of a crack on the leg, many owners hastily get rid of the damaged product, but a couple of tools and glue will help to save and eliminate the defect.
If the damage is at the top or in the place where the screws are fastened, the following set of consumables and tools will eliminate the crack:
- sandpaper;
- grinder;
- drill with small diameter drills;
- epoxy resin and solvent.
The edges of the crack must be drilled to stop further cracking. Strip the crack along the entire length and degrease the surface. The space inside the crack must be filled with resin or glue similar in properties.
After this, you need to leave the toilet for a day until the adhesive is completely crystallized. The next day, grind the seam.
If a puddle began to appear under the toilet, then it's time to change the cuff. This seal is used to seal the connection of the sewer pipe with the drain of the toilet. Replacement begins with the dismantling of the worn gasket. Using a knife, you need to clean the surface of the pipes from contamination. All should be well degreased.
Then the joint is treated with sealant. A new cuff is inserted into the sewer hole and is worn on the toilet drain. On top, you can additionally take silicone sealant and apply on contact surfaces.
When installing the cuff, special silicone sealants must be used to achieve maximum tightness of the connection to the walls of the sewer hole
The toilet may become clogged after prolonged use. To clean hard-to-reach surfaces, you will need a plunger, plumbing cable and chemicals.
First you need to clean the drain with a cable and plunger. Then fall asleep "chemistry" and wait a certain time. In the process of working with chemicals, goggles, a mask and clothing should be used that completely covers the skin. After chemical reactions, flush and once again treat the bowl with a plunger and a cable.
# 7: Lift broke on the lid
With ordinary covers, the owners do not "bother", buying a new one after wear, as it is inexpensive, and the market offers models for every taste. Products with a microlift are much more expensive. The slow lowering mechanism could break due to forced closure.
To restore the lift, the lateral mounting screws often help. If this does not help, then you need to change the whole mechanism.
The version of the microlift presented in the photo is subject to replacement, in addition, it is easy to purchase. However, there are models with built-in devices for smooth lowering, in which case you will have to completely change the seat
Proper operation of the installation system
The room where the installation of the wall mounted toilet is made acquires a special charm. It is for the sake of improving the interior that many choose installation systems. This contributes to faster cleaning of the room, since all engineering parts are hidden behind the wall, including valves and pipe wiring.
When installing the installation for the toilet, do not forget about the practical side, leaving a hole in the wall niche for servicing the tank
When installing such a product, it is necessary to leave a place under the audit compartment, through which it will be possible to make an inspection and dismantle it.
The main enemy of any plumbing is water and those impurities that it carries in itself. Its aggressive composition can lead to clogging and rust during the year. Therefore, it is recommended to use filters at the entrance to the tank.
The presence of at least a coarse filter will significantly reduce the accumulation of dirt inside the tank, which will certainly increase its service life.
Do not forget to purchase a repair kit along with the purchase of the system. In the future, the search for compatible components may become more complicated, especially for foreign-made products that use non-standard and unique tank drain designs.
The video will help to avoid errors during installation and improve understanding of the repair process.
The advice of experienced engineers will allow you to quickly find the cause of the malfunction in your installation to the toilet and quickly fix it. Learn the principle of the drain system, and you yourself can find the cause of the breakdown.
And what kind of breakdowns have you encountered during the operation of the installation for the toilet? Talk about personal experiences and ask questions in the comments to the article.