Are you looking for an unpretentious and easy to use electric pump for irrigation and water supply of a country house? Agree, it would be good to buy an inexpensive unit that can perform the functions assigned to it for many years without interruption.
Perhaps you were interested in the Agidel water pump, about which neighbors in the area spoke flatteringly? But do you doubt its operability and the appropriateness of such an acquisition? We will help you familiarize yourself with the details of this pump - the article gives its characteristics, pros and cons, as well as features of installation and connection to the system.
The operating rules are also given, the implementation of which can significantly increase the service life declared by the manufacturer, selected photo materials, relevant schemes and thematic videos that reveal the nuances of preparation for launch and the subtleties of regular use.
Model range and manufacturers
As testimonials from consumers and experts, Agidel really is a reliable and durable equipment. Moreover, these electric pumps have long been known to summer residents and gardeners throughout the CIS.
Agidel electric pumps belong to the type of surface centrifugal pumps and are manufactured by PromGrupp LLC - the receiver of the Ufa Aggregate Production Association, which has produced electric pumps under the Agidel brand for more than 50 years.
Over the years, the design of the pump has not fundamentally changed, except that for the manufacture of some parts they began to use high-strength polymers instead of alloys.
It is worth noting that the Ufa enterprise produces all the components for Agidel electric pumps on its own, and the build quality is highly appreciated by specialists.
The cost of these electric pumps is 2-5 times lower in comparison with imported counterparts, and they are almost inferior to world brands in terms of performance, reliability and durability.
The Agidel series of surface centrifugal pumps is designed for intake and transportation of water from open reservoirs, shallow wells, wells
The range of Agidel pumps cannot be called diverse; there are only two models in it:
- Agidel-M - a small-sized electric pump used to supply water from a shallow depth of up to 8 m and over short distances. Available in vertical, horizontal and universal format.
- Agidel 10 - a medium-power pump of a self-priming type, capable of lifting water from a well or well up to a depth of 7 m. It is available only in horizontal design.
Both versions are equipped with a centrifugal-type discharge mechanism, which is driven by a single-phase motor operating from a 220 V mains.
If we compare both pumps, the “ten” looks more preferable: this unit has a 33% higher head and 14% productivity, however, the power consumption is 2 times higher than that of the “M” modification.
Models "M" and "10" are improved versions of the first pump of the BC series of Ufa manufacturers, which was produced for more than forty years
Perhaps you will find useful information on the top ten centrifugal pumps on the market.
Technical characteristics of pumps Agidel
Electric pumps "Agidel" can be used for pumping water from open reservoirs, shallow water wells, wells. Pumps are able to work for a long time, thanks to the presence of special protection against overheating.
Agidel-M Series
The electric pump "Agidel-M" belongs to the class of small-sized pumps, its weight is 6 kg and its dimensions are 24x25 cm. The unit is used for pumping water with a temperature of not more than 35º C.
The suction height, characteristic of most modifications M, does not exceed 8 m. However, if the unit is equipped with an ejector, this figure will increase to 15 m.
Between the bottom of the suction valve and the bottom of the intake source should be more than 0.3 m. Before starting the pump requires filling with water.
The monoblock design of the Agidel M pump includes two main components: a centrifugal pump and an electric motor designed for continuous operation
The maximum pressure of water created by the pump of this brand is 20 m, capacity - 2.9 m3 / hour. Model “M” belongs to the class of economical equipment for pumping water, its power consumption is 370 watts. The mains voltage is 220 V.
Agidel brand electric pumps are not designed to operate at sub-zero temperatures, therefore insulation is required for operation in winter.
For example, when using a pump for a well, an insulated caisson is arranged, buried below the level of soil freezing.
The pump housing is made of high-strength aluminum, so the unit is lightweight, allowing you to install it on almost any flat surface
Agidel-10 Series
Unlike the “M” model, the “Agidel-10” electric pump is a more powerful and large-sized device. Its weight is 9 kg and its dimensions are 33x19x17 cm. Operation of the unit without filling with water is prohibited, otherwise the mechanical seal is malfunctioning.
The suction height of this modification is 7m. The pump provides a maximum design head of 20 m, which is the sum of the suction, discharge and losses in the pipeline.
Productivity is 3.6 m3 / hour. The installation method is horizontal. "Ten" consumes exactly two times more electricity - about 700 watts. It works from a single-phase power supply network with a voltage of 220V.
Unlike the previous model “Agidel-10” cannot be understaffed with an ejector. The body of the electric pump is made of aluminum alloy.
The structural parts of the Agidel 10 pump are an electric motor, a centrifugal and a jet pump
Purpose and scope
Surface pumps "Agidel" are popular among summer residents and owners of country houses. Units are installed on a flat surface in special containers, utility rooms or under a canopy to protect against rain and sunlight.
Despite the suitability for working with open water bodies, it is desirable that the pumped water undergo preliminary filtration. For example, when using the unit for pumping water from a well, it recommends a bottom filter device.
Image Gallery
Photo from
Components of Agidel pumps
Agidel pump in the water supply system
Use of pumping equipment by summer residents
Performance and terms of use are marked on the case
The scope of the pumps is quite limited, but it fully meets the needs of the owners:
- autonomous water supply system at home;
- irrigation of agricultural crops;
- water supply to water consuming household appliances;
- filling / pumping out pools and reservoirs;
- water supply from a well, a well, an open reservoir.
Agidel pumps are not recommended for pumping water from flooded basements, as in most cases, the water will contain large suspended particles that will quickly disable the unit.
Your pump has stopped pumping water and you do not know what to do? Perhaps you will find useful information on repairing a pump of the Agidel brand.
If you plan to operate the pump in the winter, then you need to take care of the insulation device so that the temperature of the environment surrounding the pump is above zero
Device and principle of operation
Electric pumps "Agidel" have a simple monoblock design, characteristic of all centrifugal surface pumps.
From the time of the first version of “Agidel-BC”, the unit's device remained the same, only special protection against overheating appeared, allowing the pump to be operated without interruptions for a long time.
An electric pump marked M consists of two main parts: an electric motor and a centrifugal pump. In the “Ten”, a set of an engine and a centrifugal pump is supplemented by a jet pump.
It is entrusted with ensuring “self-priming” of the water supplied to the system by a centrifugal counterpart.
The electric motor, which serves as a drive for the pump, includes a stator with a built-in thermal fuse that protects the winding of the mechanism from overheating.
The electric motor also includes a rotor, a bearing shield, and a flange. Cooling during operation is carried out by a vane fan, which is closed by a cap-hood.
The principle of the pump is based on the action of centrifugal forces, due to which the unit provides water supply. The source of centrifugal force is the impeller located on the rotor shaft.
Cuffs are located in the flange that protect the motor from water entering it.
Electric motors of all modifications of Agidel pumps must be carefully protected from the slightest ingress of water - the main reason for their failure
Water enters the pump through a suction valve, which also serves as a filter to prevent foreign objects (large particles, debris, rock debris, etc.) from entering the pump.
This valve in the model “Agidel-M” plays the role of a shut-off valve when priming the pump before starting.
The housing connector and flange are sealed with a rubber gasket. Model “M” is additionally equipped with a screw for bleeding air. To install the pump in a vertical position in the housing there are mounting holes. For horizontal placement are the holes in the rack.
The Agidel-10 pump is equipped with a four-wire power cord for connecting to the mains, which is reinforced with a plug with an integrated grounding contact
Operation of pumps "Agidel"
When installing the pumps, three conditions must be observed:
- Installation and operation should be carried out at a positive ambient temperature.
- Operation of Agidel units without grounding is prohibited.
- The pump must be installed on a level surface.
It is recommended to reduce the distance between the water source and the pump. The smaller it is, the more efficient the pumping is.
In addition, the unit needs reliable protection against precipitation and from direct exposure to sun rays heating the case.
The best option is to install a warmed caisson or a special container for the pump. If winter operation is planned, then it is necessary to insulate the place where it will be located.
Well, if you can install in the basement or utility room at home. However, it must be understood that the unit will be removed from the place of water intake, which means that its pressure characteristics will decrease.
Rule # 1 - preparing the pump for operation
The most important thing in the preparatory work is to install the pump so that water does not get into the electric motor. Before starting the pump, it is necessary to check the suction valve, pour 500 ml of water into it.
In case of the slightest leakage from the drainage hole in the unit flange, the operation should be stopped, the pump should be disassembled and the sealing cuffs replaced.
All nodes of the Agidel electric pump connection must be tight. The joining points of the valve and the nipple with the hoses connected to them must be tightened with clamps, in extreme cases, with wire.
For threaded connections, it is recommended to use FUM tape, linen tow, sealing thread of the TangitUnilok type.
It is recommended to think over the installation scheme with a minimum number of connection points. The connection should not be subjected to frequent dismantling, as in this case, its tightness is lost.
The connection of the water pipe with the inlet valve should be made using a rubber hose with a wall thickness of at least 4 mm and an inner diameter of 25-30 mm.
The socket for connecting the pump to the mains must be installed indoors or under a canopy. The electric pump must be grounded!
Grounding can be arranged using bare steel wire, one end of which is connected to the pump, and the other to the ground electrode, which can be used as metal structures
Rule # 2 - fill with water before starting
The Agidel-M pump must be filled with water before each commissioning. The meaning of the filling is to squeeze out air from the pump through a shut-off valve and fill it with a working fluid.
Pour 1.5 liters of clean water through the funnel intended for filling in 4 to 5 minutes. before starting.
Pouring water into the electric pump can be done using a vacuum pump or ejector. In this case, the pumping of air lasts until the moment when the equipment begins to pump water.
This is a rather time-consuming method, usually used only for large pumping stations, however, it can also be used for Agidel electric pumps.
When pouring modifications with the letter M, it is better to give preference to schemes that exclude the possibility of sucking air through the funnel.
When using pouring schemes with a likelihood of suction, it should be noted that if the water level in the funnel decreases, it can cause air suction, due to which the unit will immediately stop operation.
Do not operate the surface unit without first filling it with water, because this may damage the mechanical seal.
Rule # 3 - Operational Safety
The correct operation of the Agidel electric pumps comes down to following the manufacturer's recommendations and electrical safety standards.
Let's consider them in more detail:
- Do not use a surface centrifugal pump at great depths.
- Do not allow dry running, i.e. operation without preliminary filling.
- It is necessary to carefully protect the motor from water entering it, as it will immediately break it.
- Do not allow the operation of the electric pump without grounding.
- Do not touch the body of a running unit.
- Do not use the electric pump for pumping chemical media.
To ensure smooth starting and stopping, the Agidel pump can be equipped with an individual water supply controller (KIV), which reduces the risk of overheating of the electric motor and prevents water hammer in the system.
KIV provides automatic shutdown of the pump in case of hydraulic system malfunctions: breakage of a hose or pipeline, decrease in water level in a water source
Rule # 4 - Maintenance
The manufacturer determines the life of the Agidel electric pumps to 5 years. Of course, subject to all the rules for connection and operation, as well as safety precautions, the pump can last much longer.
Throughout the entire service life, Agidel pumps do not require special maintenance.
When using the pump as a pump for summer watering and periodic water supply at home, at the end of the season, it is necessary to disassemble the electric pump to clean the fan and working shaft from adhering dirt and deposits.
It is also necessary to lubricate the rubbing parts. Winter storage of the pump is carried out in a dry place at a plus temperature.
Agidel pump failures usually occur after 5 years of operation and are associated with a hose rupture or wear of the stuffing box. In the first case, the hose is replaced with a new one, and in the second, the gland is changed using the repair kit.
Image Gallery
Photo from
Replacing engine shaft seals
Removing the pad holding bolts
Removing pump pump to replace seals
Removing worn motor shaft seals
Removing Damaged Oil Seals
Sealing of elastomer seals
Installation of a pressed-in gland
Assembling the pump in reverse order
Advantages and disadvantages of Agidel pumps
The Agidel centrifugal surface electric pump is a reliable unit used for irrigation or for supplying water from a source to a water consumer.
The pumps “Agidel-M” and “Agidel-10” have many advantages:
- low cost;
- ease of maintenance and operation;
- maintainability;
- low power consumption, especially the “M” model;
- electrical safety;
- reliability, durability.
The disadvantages of electric pumps "Agidel" include the inability to use at a depth of more than 7 m (10 m) and the need to be located near a water source.
Please note that currently there are many fakes of Chinese-made Agidel pumps, the case of such units is made of plastic, and the build quality is very poor.
The original Agidel pump is manufactured only by PromGrupp LLC in Ufa, the electric pump casing is made of metal, the manufacturer gives a guarantee for equipment for thirty months
Preparation for operation and start-up of the Agidel-M pump:
Video review of the Agidel-M pump (interview with the manufacturer):
Russian-made Agidel pumps are inexpensive and reliable units that are excellent for seasonal use. Electric pumps have both their advantages and disadvantages.
When choosing a pump, it is recommended to immediately think about the place of its placement, as excessive distance from the water source significantly reduces productivity and pressure. Subject to all installation and operation rules, the Agidel pump is able to last at least 20 years..
Do you use the Agidel pumping unit in the country? Or just planning to buy this pump, but have any questions? Feel free to ask your questions in the comments to this article.