Have you decided to lay electrical wiring in a new cottage yourself or upgrade the existing network in your apartment? Agree, in this area there are nuances that should be thoroughly dealt with for the sake of their own security. In addition, a self-made electrician is obliged to ensure the perfect operation of devices.
We are ready to tell you in the finest details how to connect a light bulb through a switch. In the implementation of such a solution, a number of proven methods are used, which you will become familiar with while reading the article.
Here you will find a lot of useful information. Possession of information will give both confidence and strength. A thorough understanding of the issue will help graphic materials and videos.
Electrical Safety Measures
Previously, before the start of the installation of switches, lighting fixtures, their connection to each other and the network, it is necessary to disconnect 220V power from that part of the home wiring where electrical work is supposed to be carried out.
This is done on the input electrical panel by disabling the common or corresponding group switch.
To avoid personal injury, do not work at height from a stepladder, but from a table or other spacious, stable surface.
If during installation the access to the panel is possible for unauthorized persons (for example, located on the stairwell of an apartment building), a poster with a warning sign “Do not turn on!” Must be placed.
Make sure that the voltage on the exposed contacts of the existing electrical appliances and wiring is absent, it is necessary immediately before work. The easiest way to do this at home is to use an indicator screwdriver, the health of which, shortly before testing, is checked from the working network.
It is recommended that before taking contacts and wires with your bare hands, make sure once again that there is no voltage by touching the back of your hand, fingers of your right hand alternately to all of them. Dry, intact skin on the back of the hand has increased resistance to electric current.
The essence of connecting the lamp through the switch can be visualized on a demo stand:
Image Gallery
Photo from
Visual connection diagram on the stand
Power Line Connection
Connect the lamp to the power line
The principle of operation of the lamp through the switch
Work Tool
In the process of electrical work being performed, the home foreman will need a set of the following installation tool:
- Sharp knife.
- Pliers (pliers).
- Side cutting pliers.
- Thin and medium slotted screwdrivers, possibly a medium cross.
Insulation may be required for insulation inside the junction box or lamp housing of the wire connections. In these cases, it is recommended to use the HB tape. Over time, it does not melt and does not stick to the constantly heating contacts isolated by it, but only dries up. If necessary, crumbles well with pliers.
Before proceeding to the most simple installation, draw a wiring diagram for electrical appliances as you will understand, and think over the procedure
It’s great if there is a special wire stripping tool - a stripper or wire cutters with cuts to remove insulation. In the absence of such devices and a large amount of work, you can get by with a folk remedy by finalizing the side cutters.
To do this, the opposite cuts are made with the file in the cutting edges closer to the hinge, which together should form an opening the size of which is slightly larger than the diameter of the exposed wire core.
Recommended cables and wires
For the new installation of home lighting electrical networks, it is recommended to use VVGNG cables with single-wire copper, 1.5 square mm cross-section, in non-combustible insulation of unequal color cores:
- blue - zero working,
- yellow with a green stripe along - zero protective (grounding),
- any other color - phase.
During installation, it is desirable to observe a combination of uniformity of colors with their functional purpose. This requirement will protect and simplify further maintenance of the electrical wiring.
When making a new wiring, wherever provided for by the design of electrical appliances, be sure to connect a zero protective (grounding) core and do not use it for other purposes
In houses where the wiring is still aluminum, the replacement of certain sections of the lighting lines, which are patched up with plaster, must be carried out with an APPV-1.5 wire having aluminum conductors or a similar cable with open laying. The same material is used due to the oxidation of the junctions of twisting aluminum and copper inside the junction boxes.
If it is possible to replace the twist with terminal connections, copper wiring is allowed. It is strongly not recommended to use any cables, wires with multi-wire (soft) conductors.
Junction box application
Cables, wires do not go directly from the shield to electrical appliances, from switches to light bulbs. All outgoing, incoming electrical equipment lines are found in specific assemblies called junction boxes. There they communicate in a certain way.
The following article will familiarize you with the rules for installing junction boxes, also called junction boxes, junction boxes, on the slang of electricians. We recommend that you familiarize yourself with useful material.
Most often, boxes have empty space inside. The wires of different lines are then interconnected using twists. To ensure reliability, it is recommended that the tails of the joints be treated with special welding. Copper cores can simply be soldered.
Before laying inward, open contacts are insulated from each other with CB tape. It is possible to screw special insulating clamps onto twisted wires. Here the insulating tape is no longer needed.
Do not use PVC type electrical tape to insulate twists - over time, it will stick to the contacts so that it will be difficult to remove if necessary
If the box is equipped with screw terminals, then the contacts are made with the participation of them. Such devices allow you to connect aluminum conductors and copper. The clamping terminals can be used, but this is when there is enough space for laying the ends of the wires connected by them.
Stripping insulation
To remove part of the external insulation of the VVGNG cable, a knife is required. It should be so sharp that even an inexperienced home master could make sure cuts.
The first cut is made from the end along the sheath by 3-4 cm. After that, with one hand they take on the bundle of loose extremities of the wires, and the second one pulls on the incised shirt. Then she tears herself.
The depth of the tear is such that the released ponytails of the wires are of the maximum length that the junction box, socket box or housing of the lighting device allows to lay. The stock will serve faithfully in the future when burning weakened contacts.
A torn cable jacket is turned inside out and carefully, so as not to damage the insulation of the wires, it is cut round.
The veins are most easily cleaned, of course, with a tool for removing insulation - a stripper or at least side-cutting pliers with slots.In the absence of these, the knife is used the same way as before. The use of simple side cutters is allowed. In extreme cases, biting edges of pliers are used.
Removing the outer sheath from the cable. it is important not to cut the insulation of the wires, and stripping the insulation of the wires - not to damage the metal surface of the wires
With light movements of the tool in a circle, they cut shallow into the insulation and tighten it. The main thing is not to cut through the metal of the conductor, otherwise where there is damage, it will necessarily break off. Well, if immediately, and not after installation.
The size of the exposed area is determined by the connection method. When it is the screw terminals of the terminals of the box, switch, chandelier or sconce, 0.5-1 cm may be enough. For twisting with the wiring of the lamp it will take 2-3 cm.
If the twists are located in a junction box, the rule applies, the more the better, especially without soldering or welding. Usually 3-5 cm.
When using screw-on insulating clamps, clamping clamps are individually tailored to the stripping length.
The nuances of twisting
When twisting two wires, their exposed ends are folded with the letter “X” so that the intersection is at the beginning of the insulation. Then the ends of the cores are clamped with fingers and twisted as much as possible. Next, the process is helped with pliers.
Three wires and more are connected in the same way. If the connection comes out long and flexible at the same time, it is folded in half, pressing on with pliers. Shortened twisting requires less electrical tape.
The greater the length of the peeled cable tails, the easier it will be to twist, and the more reliable the contact will be - and the excess can always be cut
The electrical tape begins to overlap with the factory insulation of the twisting wires to the width of the tape. After passing in a single layer until the end of the exposed tails, a couple more revolutions are made, as if to catch air. This "emptiness" is bent back to twist - a protected end is obtained, and the second row dominates with the mandatory entry to the main insulation of the cores.
Correct installation of the switch
According to the execution of the circuit breakers are indoor and outdoor installation. Modern outdoor switches are suitable for mounting on any surface without additional insulating stands. Internal switches are hidden in round sockets in the wall, equipped with special cups called podrozetniki.
How to install this mounting box in a concrete wall or in a structure made of drywall is described in detail here. We advise you to read the proposed article before starting work.
Podrozetniki - a standard wiring assembly. They are also used to equip outlets, so they are called so. “Sub-switches” would not sound very much.
The location of the switch is considered to be correct, in which switching on occurs by pressing the top of the key, switching off - the bottom. This makes it possible even for a short person to respond in an emergency and promptly de-energize the appliance by striking the key with the fingers from top to bottom.
Position the switches on the walls so that they do not need to be "searched, shaking hands in the dark," and all family members could easily use them
With proper connection, a phase wire comes to the switch from the junction box. To interrupt the phase wire circuit so that the lamp is without voltage in the off state is the main task of the switch.
The following photo compilation illustrates the connection process:
Image Gallery
Photo from
Step 1: Circuit with 2-key switch
Step 2: Junction box for connecting the lamps
Step 3: Wire Harnesses in the Junction Box
Step 4: Connect the zeros in the junction box
Step 5: Connect the phase conductor to the switch
Step 6: Installing the lid of the junction box
Step 7: Checking the connection of the bulbs
Step 8: Turn on two lamps with two keys
If the design of the device allows, inside the circuit breaker itself, the phase wire is connected to the upper terminals, and all outgoing conductors are connected to the lower contacts. This rule applies to the arrangement of any electrical installation.
Due to the design features, an exception to the general rules is through and cross switches, which are discussed below.
Varieties of household switches
The switches used in the modern home interior are diverse. One of the popular articles posted on our website introduces in detail the classification of light control devices.
When choosing a home switch, pay more attention not to its design, but to the functionality, strength of the mounts and the reliability of electrical contacts
By the difference in their functionality, the following most common varieties are distinguished:
- Single-key switch - his mission is simple: "on / off."
- Two-gang switch allows you to control simultaneously two independent lighting circuits.
- Three-key switch, accordingly, coordinates work in three directions.
- Switch-regulator (dimmer) not only turns on and off, but also by pressing a key or by turning the round knob that replaces it, smoothly adjusts the brightness of the light of the lamps.
- Switch with regulator - a two-, three-key switch, which stepwise, by switching keys, controls the incandescent light of all bulbs simultaneously.
- Single pass switch. The only key throws the phase between the two wires. If voltage is applied to one, it is disconnected from the other, and vice versa.
- Cross single switch. By changing the position of the key, the direct connection of two lines to the cross synchronously changes.
- Sensor switch. It has no levers - it starts and stops the supply of electricity with the touch of a finger to its surface.
A switch with a motion sensor ignites the lamp automatically, reacting to a person passing by.
Types of lamps for home use
Tube progress does not lag behind switches. Their variety is also impressive.
When purchasing an energy-saving light bulb, you should focus on well-known brands - because it should not only be effective, but also serve as long as possible
But here, some more common types are defined:
- Incandescent lamps - rooted domestic light sources in a rounded glass bulb with a vacuum and a tungsten spiral inside.
- Halogen lamps - the same incandescent lamps filled with special gas. It increases the service life, minimizes the size of their flasks. Disadvantage - during installation, do not touch the glass of the bulb with your hands.
- Fluorescent tubes - common at home, not very, but also traditional lighting devices (hereinafter simply “fluorescent lamps”).
- Energy-saving LED lamps, based on the name, use the glow of groups of LEDs. They can be fixed in ordinary screw-in cartridges (hereinafter simply “LED lamps").
Energy-saving fluorescent bulbs are increasingly replacing conventional ones. The principle of operation is similar to the action of fluorescent lamps. Screw in like incandescent lamps (hereinafter simply “energy-saving lamps”).
Ways to power a light bulb through a switch
Perhaps some of the scheme under consideration for the mutual connection of a household switch to a wall or ceiling light will omit the details of supplying a zero protective (grounding) wire. It seems that connecting it will not cause difficulties.
In a standard electric cable, this is a core with yellow insulation and a green stripe along it. The place of its connection to the appliance is indicated by .
# 1: The simplest connection of the lamp
The most elementary is the on / off connection of the lighting device to a single-key switch with two wires. Most of all it is suitable for a single single-lamp luminaire.
When developing new circuit breakers, manufacturers adhere to the standards - replacing the usual “single-key” electronic device will pass without problems
When the old wiring has only two wires leaving the ceiling or wall that feed the light electrical appliance, and the alteration is complicated, you can connect a lamp with more lamps. But with this connection, all the lights of the lighting device will turn on at the same time.
A classic single-key switch without upgrading the wiring can be easily replaced with a light dimmer switch-dimmer, made in a single unit. It is possible to purchase a device with a regulator like a key, or it is possible in the form of a round knob.
The characteristics of the dimmer must correspond to the power of the connected luminaire. The only thing is that it cannot be used in conjunction with lighting devices equipped with energy-saving, LED or fluorescent lamps.
For standard installation in conventional socket boxes, the industry has mastered the production of touch switches with only on / off functions. They are also connected by two wires and can replace simple single-key ones.
# 2: Separate inclusion of chandelier lamps
Usually, three- and five-arm chandeliers are arranged so that the lamps can be connected separately or in groups (1 + 2/2 + 1; 2 + 3/3 + 2). This allows you to adjust the illumination of space by the number of simultaneously working light bulbs.
If possible, it is better to attach the ground wire to the chandelier directly, and not through the terminal block - this will increase the safety of the lamp
In this case, you need a two-key switch and electrical wiring with at least three wires. By turning on one of the two or both keys at once, the brightness of the lighting fixture will be adjusted.
Another switch with two keys is used to control from one point the lighting of two, most often adjacent, rooms independently, for example, a toilet and a bathroom, an entrance hall and a pantry.
If instead of the usual two-key switch you use a two- or even three-key for a chandelier with separate regulators built into the keys, then all its lamps will light up simultaneously, and you can control their incidence in steps, by switching the keys.
# 3: five-arm chandelier control
Where separate and simultaneous control of three independent lighting devices is required, a three-key switch is installed.
When connecting the switch to the circuit, make sure that the phase wire comes from the box - always try to put it on the top terminal
To surprise guests, you can connect a five-arm chandelier through a three-key switch. True, a small alteration at the terminals of the lamp itself will be required. From a group of three line wiring, one must be disconnected and used independently.
Then, by various combinations of pressing the keys of the three-key switch, it will be possible to turn on simultaneously from one to five lamps (1 + 2 + 2/2 + 2 + 1/2 + 1 + 2).
# 4: Lamp - one, switch - two
What to do when the corridor is long and dark? This situation will help to resolve the installation of the luminaire immediately with two single-pass through switches at different ends of the transition. The disadvantage of this method is the indefinite position of the on / off keys.
Another such lighting control technique is applicable when moving up stairs, in an attached garage (entrance from the house, exit through the gate and vice versa). An additional switch near the sleeping area will not become an excess if the room is quite long.
Using in practice non-standard schemes for connecting fixtures, you should make sure that they are practical, as this increases the length of the wires and the complexity of installation (+)
Is it possible to independently illuminate the flights of stairs, climbing or descending the stairs? In addition, you will need another single pass switch on the floor. By pressing just one key, it will simultaneously turn on the next lamp and turn off the previous one.
# 5: Turning on the light bulb from different places
To control the luminaire from more than two centers, in addition to the walk-through, cross-type single switches are required. Each new point - one at a time.
A lot of switches are convenient if living rooms go into the extensive home lounge. Inhabitants of any room will be able to turn on the lights at their doors independently and turn off in all other places equipped with auxiliary switches.
With the correct organization of the installation locations of additional switches, in addition to the convenience of using lighting, significant energy savings can be achieved
This method is also advisable in rooms with a hotel-type layout - many doors opening into a long corridor.
# 6: Connecting a chandelier with a fan
Pulling a hanging bag on a chandelier equipped with a fan to turn it on is inconvenient. It is also problematic when the ceiling is high.
It is easier to use the studied methods for separately connecting the chandelier lamps. The fan is connected via one of the keys of the two- or three-key switch.
In the first version, the lamp can only burn completely. In the second, the bulbs will be lit in two groups.
# 7: Built-in motion sensors
The motion sensor itself is already a switch device. But we are interested in it, precisely when it has a standard case and can be mounted in a socket box.
It turns out that it is connected to the gap of the phase conductor going to the lamp as a normal switch. But the problem is that for the internal electronic circuit of such a device, a full 220V power supply is required, which means another wire, blue, zero.
In accordance with the principles of connecting the luminaire, motion sensors (1) are connected via a switch. If there is a need for periodic continuous operation of the lamp, a switch (2) is included in the circuit. If one sensor cannot cover a large room, then several pieces are connected to the lamp. In this case, it is the sensors that play the role of a switch (3)
If you want to install a switch with a built-in motion sensor instead of a single-key, you can not do without replacing the two-wire wire that stretches towards it from the junction box with a three-wire one.
The videos will introduce practical working methods.
VIDEO №1 will show an example of a simple connection of a switch and a bulb:
VIDEO №2 will help to master the skills of connecting and insulation of wires:
VIDEO №3 tells how to connect chandeliers and not only:
Manufacturers in one place are not marking time. They come up with newer, more sophisticated lighting fixtures. But no matter how cosmic the lamp may seem, there is always a simple way to connect it. The main schemes, the rules for connecting bulbs with switches, the conditions for safe electrical installation will remain typical for a long time.
Do you want to share the experience of an independent electrician, interesting and useful nuances of connection, have you found any flaws in the material presented? We are waiting for your comments. Please write in the block below, post a photo on the topic, ask questions.